Skip to main content

Vantage Plumbing and Heating

Are Magnetic Boiler Filters Worth It? An Engineer’s Answer

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

Yes, for almost every gas boiler and wet central heating system a magnetic filter is worth fitting: it is a small part that catches the black iron sludge, called magnetite, before it can clog the boiler’s heat exchanger and pump. It only earns its place if it is cleaned out at every annual service, and it is not a cure for a system that is already full of sludge, which needs cleaning first.

  • Radiators and steel pipework slowly corrode inside, producing magnetite sludge.
  • A magnetic filter sits on the pipework returning to the boiler and uses a strong magnet to catch that sludge.
  • It protects the boiler’s narrow waterways, heat exchanger and pump, which are the parts sludge damages most.
  • It needs emptying at every annual service, and works alongside inhibitor, not instead of it.
  • On a dirty system, clean it first with a power flush or chemical clean, then fit the filter to keep it clean.

What a magnetic filter actually does

Inside every wet central heating system, the water slowly reacts with the steel of the radiators and the iron in other parts. This corrosion produces magnetite, a black iron oxide. It starts as fine particles circulating in the water and gradually settles as a thick black sludge in the bottom of radiators and in the narrow passages of the boiler.

A magnetic filter is a small canister fitted on the heating pipework, usually just under the boiler. Inside is a powerful magnet in a sleeve. As the system water flows through, the magnet pulls magnetite particles out of the flow and holds them. At the annual service the engineer isolates the filter, removes the magnet, and the collected sludge rinses away.

Many modern filters are dual action: as well as the magnet, they have a mesh or a flow design that also catches non-magnetic debris such as sand, flux or bits of limescale.

Why sludge matters

PartWhat sludge does to itWhat you might notice
RadiatorsSettles at the bottom and blocks flowCold at the bottom, warm at the top
Boiler heat exchangerBlocks its narrow waterways and causes hot spotsKettling or banging noises, overheating faults
PumpWears the bearings and can seize itPump noise, no heat, pump or flow faults
Diverter valve (combi)Sticks or jams the valveHeating or hot water not switching properly
Valves and pipesNarrows small bore pipeworkSlow warm-up, uneven heat around the house

Modern condensing boilers have much narrower waterways than older boilers, which makes them more sensitive to debris. That is the main reason filters have become standard on new installations. If your radiators are already cold at the bottom, our guide to a radiator not heating up explains the signs, and our power flushing service is the usual way to clear it.

When a magnetic filter is worth it

SituationWorth fitting a filter?Why
New boiler going inYesProtects the new boiler from sludge already in the system and any that forms later
Existing boiler, reasonably clean systemYesCatches sludge before it builds up in the boiler
System full of sludge, cold radiatorsYes, but clean the system firstA filter would fill up quickly and cannot clean radiators already blocked
After a power flushYesKeeps the system clean after it has been cleaned
Open vented system with a regular boilerYesThe loft tank lets more oxygen in, so these systems can produce more sludge
Plastic pipework throughoutStill usefulSteel radiators and other parts still corrode

Every new boiler package we install includes a magnetic system filter, along with the first year’s service and removal of the old boiler. You can price a new boiler with our boiler quote tool.

What a filter will not do

A magnetic filter is good at one job. It does not replace the other parts of looking after the water in your heating system.

  • It does not stop corrosion. Inhibitor does that. Inhibitor is a chemical added to the system water to slow corrosion and scale. The British Standard for treating water in heating systems, BS 7593, covers cleaning, inhibitor and ongoing checks. A filter catches what corrosion still produces.
  • It does not clean a dirty system. Sludge sitting in the bottom of radiators is not moving, so it never reaches the filter. A power flush or chemical clean is needed to remove it.
  • It does not fix the cause. If a system is constantly losing water and being topped up, fresh oxygen comes in with every top-up and corrosion speeds up. The leak needs fixing.
  • It does not work if it is never emptied. A full filter cannot catch any more, and a badly neglected one can restrict flow.

How a magnetic filter is fitted

A filter is a job for a heating engineer. A typical fit:

  1. The boiler is switched off and the heating side is isolated or drained down as needed.
  2. The filter is fitted on the return pipe, the one carrying water back into the boiler, so it catches debris before it enters. It is positioned so it can be reached for servicing.
  3. Isolating valves on the filter let it be cleaned without draining the whole system.
  4. The system is refilled, the pressure reset on a sealed system, and air bled out.
  5. Inhibitor is checked and topped up. Many filters have a dosing point that makes this easy.

Filters come in sizes to suit 22mm and 28mm pipework, and compact versions exist for tight spaces under the boiler.

Cleaning a magnetic filter

Manufacturers such as ADEY recommend the filter is cleaned every year as part of the boiler service. The engineer:

  1. isolates the filter with its valves
  2. releases any pressure through the vent
  3. removes the cap and lifts out the magnet in its sleeve
  4. rinses the collected sludge away, using non-metallic tools so the parts are not damaged
  5. checks the seal, refits the cap, reopens the valves and bleeds any air
  6. tops up the inhibitor and checks the system pressure

The amount of sludge in the filter is useful information. A filter that is packed with black sludge every year tells the engineer the system is corroding faster than it should, which usually points to low inhibitor, a leak or air getting in.

Before you touch it

  • Do not open a filter on a sealed system without isolating it first. It is under pressure and the water may be hot.
  • Never remove the boiler casing or work inside a gas boiler. Only a Gas Safe registered engineer may.
  • If you drop the system pressure while cleaning, it will need repressurising with the filling loop to the figure in your boiler’s user guide.
  • If you are not sure how your filter works, leave it for your next service.

Common mistakes

  1. Fitting a filter and never cleaning it. The most common problem with filters.
  2. Fitting to a sludged system without cleaning. The filter clogs quickly and the radiators stay cold.
  3. Relying on the filter instead of inhibitor. They do different jobs.
  4. Poor access. A filter squeezed into a space where the cap cannot be removed will not get cleaned.
  5. Ignoring what the filter shows. Heavy sludge every year is a symptom to investigate.

If your system needs a proper clean first, our guide on power flushing and the signs your radiators need it explains what is involved, and how to choose a power flushing engineer covers what to ask.

What it costs with Vantage

Fitting a filter is a small job, and it is often done alongside a service, a repair or a power flush. In normal working hours there is no call-out fee. After the first hour, time is charged in half-hour steps, and parts, such as the filter itself, are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive.

New boiler installations are quoted as a fixed price after a free survey, so the price you agree is the price you pay.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Frequently asked questions

Do all boilers need a magnetic filter?

Not by law, but it is good practice on any wet central heating system with steel radiators, and many installers now fit one as standard with a new boiler. It is one of the simplest ways to protect a boiler from sludge.

How often should a magnetic filter be cleaned?

Once a year, as part of the annual boiler service, is what manufacturers such as ADEY recommend. A system that produces a lot of sludge may need checking more often until the cause is fixed.

Does a magnetic filter replace a power flush?

No. A power flush removes sludge that has already settled in radiators and pipework. A filter catches sludge that is still circulating. The best result is to clean the system first, then fit a filter to keep it clean.

Can I fit a magnetic filter myself?

Fitting a filter means cutting into the heating pipework, then refilling, bleeding and treating the system. It is best done by a heating engineer, who can also check the inhibitor level and make sure the filter is on the right pipe with room to service it.

Will a magnetic filter reduce my gas bill?

A clean system transfers heat better than one clogged with sludge, so keeping it clean helps the boiler and radiators work as designed. The filter itself does not heat anything. Its value is in stopping efficiency and reliability getting worse over time.

Heating system care in Hertfordshire, Bedfordshire and Cambridgeshire

If your radiators are cold at the bottom, your boiler is noisy or you want a filter fitted, our engineers can check the system water, clean it and protect it. See our power flushing service or call 01462 506374, answered 24 hours a day, 7 days a week.

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.