Skip to main content

Vantage Plumbing and Heating

Boiler Overheating: Signs, Causes and What to Do

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

A boiler is overheating when the water inside it gets hotter than it should, usually because the heat is not being carried away fast enough, and the boiler responds by shutting itself down, often with an overheat fault code. The most common causes are low pressure, trapped air, a failing pump, sludge or closed radiator valves, and limescale in the heat exchanger; you can safely check pressure, radiators and valves yourself, but if it keeps happening a Gas Safe engineer needs to find the cause.

In short

  • Modern boilers protect themselves: when they overheat they lock out rather than keep heating.
  • Signs include cutting out mid-programme, an overheat code, kettling noises, very hot pipes or water from the pressure relief pipe.
  • The real fault is usually poor circulation (pump, sludge, air, closed valves) or scale in the heat exchanger.
  • Check the pressure, bleed radiators and make sure valves are open, then reset once.
  • A boiler that overheats again after one reset needs a Gas Safe engineer.
Ideal boiler installed by Vantage in a fitted cupboard, with copper pipework and a magnetic system filter
One of our boiler installations: an Ideal combi in a fitted cupboard with a magnetic system filter.

How a boiler overheats

Your boiler heats water, and the pump pushes that water round the radiators and back again. As long as water keeps moving, heat is carried away from the boiler as fast as the burner makes it. If the flow slows or stops, the water in the boiler’s heat exchanger keeps getting hotter.

Boilers are built for this. A temperature sensor (thermistor) tells the control board how hot the water is, so it can turn the burner down or off. As a last line of defence, an overheat cut-out, sometimes called a high limit thermostat or safety temperature limiter, shuts the gas off if the water goes past a safe limit. The pressure relief valve, usually set to open at around 3 bar, releases water if the pressure climbs too high.

So in practice, an overheating boiler switches off. It is doing its job. The question is why the heat is not getting away.

If your boiler keeps cutting out with an overheat fault, our boiler repair service covers all the major brands, with the phone answered 24 hours a day, 7 days a week.

Signs your boiler is overheating

  • It switches off in the middle of a programme and will not restart until it cools or is reset.
  • It shows an overheat fault code. Examples include Vaillant F20, Glow-worm F20 and Worcester Bosch E9. Other brands have their own codes, listed in the user guide.
  • Kettling. A rumbling, whistling or banging sound, like a kettle coming to the boil, as water flashes to steam against hot spots in the heat exchanger. Our guide to a boiler making a banging noise covers this.
  • Pipes near the boiler are much hotter than usual, while radiators stay cool.
  • Water dripping from the pressure relief pipe outside, and a pressure gauge climbing high when the heating runs.
  • Radiators heating unevenly or slowly, which points to poor circulation.

A visible plume from the flue on a cold day is not overheating. Condensing boilers produce water vapour, and it shows up as a white plume in cold air.

Check these first

These checks are safe and do not involve opening the boiler.

  1. Note the fault code before you reset.
  2. Check the pressure gauge. With the heating cold, most boilers want around 1 to 1.5 bar. Low pressure can cause overheating and lockouts. Top up with the filling loop only if your user guide allows it.
  3. Make sure radiator valves are open, particularly if you have been decorating or have turned radiators off in unused rooms.
  4. Bleed radiators that are cold at the top. Trapped air stops water moving. Our guide on how to bleed a radiator shows how.
  5. Check the controls. Make sure the heating temperature on the boiler has not been turned right up by accident, and that the thermostat is working.
  6. Let it cool, then reset once, as your user guide describes. If the overheat fault returns, stop and call an engineer.

What not to do

  • Do not remove the boiler casing or touch the pump, sensors, overheat cut-out, gas valve, heat exchanger or control board. Under the Gas Safety (Installation and Use) Regulations 1998 only a Gas Safe registered engineer may work on a gas appliance.
  • Do not keep resetting a boiler that overheats. The overheat cut-out is a safety device, and resetting it repeatedly hides the fault.
  • If the boiler is kettling loudly or the relief pipe is discharging hot water, turn the boiler off and leave it off until it has been checked.
  • If you smell gas, call the National Gas Emergency Service on 0800 111 999, open doors and windows, do not use electrical switches and turn the gas off at the meter if it is safe to do so.

Common causes

CauseWhat you might noticeCan you fix it yourself?What the engineer does
Pump failing or seizedBoiler fires, pipes very hot, radiators cold, then lockoutNoTests and frees or replaces the pump
Sludge in the systemCold spots at the bottom of radiators, kettling, dark water when bleedingNoCleans the system, adds inhibitor, fits or cleans a magnetic filter
Limescale in the heat exchangerKettling, especially in hard water areasNoDescales or replaces the heat exchanger and advises on scale protection
Air in the systemGurgling, radiators cold at the topBleed radiatorsVents the boiler and system and looks for the cause of the air
Closed valvesRecent decorating or work, some radiators offOpen radiator valvesChecks isolation valves and zone valves
Blocked magnetic filterPoor flow after a long gap since the last serviceNoCleans the filter
Low system pressureGauge below about 1 barTop up once, per the user guideFinds the leak or failed expansion vessel
Faulty temperature sensorBoiler overheats with normal circulationNoTests the thermistor and wiring and replaces faulty parts
Diverter or zone valve faultOverheats on heating or on hot water onlyNoTests and repairs the valve

Hertfordshire and much of the surrounding area has hard water, so scale is a real factor. It builds up on the hottest surfaces inside the boiler, and a scaled heat exchanger overheats and kettles even when the rest of the system is fine.

Can an overheating boiler explode?

It is extremely unlikely with a modern, correctly installed and serviced boiler. Several independent safety devices stand between an overheating boiler and danger: the control thermistor, the overheat cut-out that shuts the gas off, and the pressure relief valve. That is why an overheating boiler locks out.

The real risks are damage to the boiler itself, scalding water from the relief pipe, and a boiler whose safety devices have been tampered with or have failed. That is why a boiler that keeps overheating should be turned off and checked rather than reset over and over.

What an engineer will check

A Gas Safe engineer will normally:

  • Read the fault history and watch the boiler run.
  • Check the system pressure, expansion vessel and pressure relief valve.
  • Check the pump is running and the flow through the boiler is right.
  • Check the flow and return temperatures across the boiler.
  • Test the temperature sensors and the overheat cut-out.
  • Check the magnetic filter and the condition of the system water.
  • Look for scale in the heat exchanger and check the diverter or zone valves.

Repair or replace?

Most overheating faults are fixed with a repair: a pump, a sensor, a system clean or a valve. If the heat exchanger is badly scaled or sludged on an older boiler, and the system has been neglected for years, replacement can be the better option. A new boiler should always be fitted with a clean system, a magnetic filter and fresh inhibitor. Our power flushing service is the usual starting point if sludge is the cause.

What we charge to fix it

Our prices, before you ring

Weekday repair visit, Monday to Friday 8am to 5pm, no call-out fee£150 + VAT
£180 inc VAT
Evenings and weekends, first hour including the call-out£297.60
inc VAT
Overnight, first hour including the call-out£330
inc VAT
If a new boiler is the better answer, fittedfrom £2,780
inc VAT

The weekday visit is a fixed price. A Gas Safe engineer comes out, finds the fault and does any small fix that needs no parts, with up to an hour on site. If the repair needs parts or more time, you get a fixed price before anything else is done. We cover Hertfordshire, Bedfordshire, Cambridgeshire and North London. Book a boiler repair, see every rate, or get a new boiler price online.

Frequently asked questions

What happens when a boiler overheats?

The control board and the overheat cut-out shut the burner off, and most boilers lock out and show a fault code. The boiler will not restart until it has cooled and, often, been reset. If it keeps happening, the cause needs finding.

Why does my boiler overheat and then cut out?

Usually because water is not flowing through it properly, so heat builds up. The common causes are a failing pump, sludge, trapped air, closed valves, low pressure or scale in the heat exchanger.

Can a boiler overheat on hot water only?

Yes. On a combi, scale in the plate heat exchanger or a faulty diverter valve can cause overheating when hot water is running but not on heating. That points the engineer to the hot water side.

What is kettling in a boiler?

Kettling is a rumbling or whistling sound caused by water boiling in hot spots inside the heat exchanger, usually because of scale or sludge restricting flow. It is a sign of overheating and should be checked.

Is it safe to use an overheating boiler?

Not repeatedly. A single lockout after a known cause, such as a closed valve you have now opened, is fine to reset once. If it overheats again, turn it off and have it checked by a Gas Safe engineer.

When to call an engineer

If your boiler keeps overheating, kettles loudly or the relief pipe is discharging, it needs a Gas Safe engineer to find out why heat is not being carried away. We are Gas Safe registered (956889), based in Stevenage, and cover Hertfordshire, Bedfordshire and Cambridgeshire with 24/7 emergency cover. Book through our boiler repair page or call 01462 506374.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.