Skip to main content

Vantage Plumbing and Heating

How to Fix a Leaking Radiator: Find the Leak, Then Fix It

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

Most radiator leaks come from the valves and joints, not the radiator itself, and many can be fixed by tightening a nut a fraction or resealing a joint. The first job is to find exactly where the water is coming from; if it is a pinhole in the radiator body, the radiator needs replacing, and in the meantime you can isolate it by closing both valves.

In short

  • Dry everything, turn the heating on and wrap tissue round each joint to find the leak.
  • A drip from under the valve cap (the spindle) often stops with a small turn of the gland nut.
  • A leak where the valve meets the radiator usually needs the joint resealing with the radiator drained.
  • Rust spots or weeping on the radiator panel mean corrosion from inside. The radiator needs replacing.
  • Close both valves to isolate a leaking radiator, protect the floor and watch your boiler pressure.
Thermal image of a radiator heating evenly after a Vantage power flush
A thermal camera shot of a radiator heating evenly across its whole surface after a power flush.

Power flush price

Cold radiators or sludge? See your fixed price now

Tell us how many radiators you have and what your system is, and you get a fixed power flush price straight away, online.

Instant power flush priceOr call 01462 506 374

First, stop the damage

  1. Put a towel and a bowl under the drip. Radiator water is often black with sludge and stains carpets.
  2. Turn the heating off if the leak is more than a slow drip.
  3. Isolate the radiator. Turn the thermostatic or wheel valve to off. On the other side, pull the cap off the lockshield valve and turn the spindle clockwise with a spanner or the cap until it stops. Count the turns so you can reopen it to the same position later.
  4. Check the boiler pressure. On a combi or system boiler, a leak lowers the pressure. If it drops below the level in the boiler’s user guide, top it up with the filling loop.

With both valves closed, the rest of the heating can usually run while you sort the leak. If the valves do not close fully, or the leak is from the pipe before the valve, call an engineer. Our central heating repairs team can take over if it is more than a simple fix.

How to find the leak

Water runs along pipes and drips from the lowest point, so where it lands is often not where it starts. To find it:

  1. Dry the radiator, valves and pipes completely.
  2. Turn the heating on so the system is under pressure and warm.
  3. Wrap a piece of dry kitchen roll round each joint in turn: the pipe into the valve, the valve into the radiator, the valve spindle and the bleed valve.
  4. Run your hand under the bottom of the radiator and along its seams.
  5. The first tissue to get wet shows you the leak.

Where radiators leak, and what to do

Where the water comes fromWhat is going onCan you fix it yourself?What an engineer does
Under the valve cap, round the spindleThe gland packing has wornOften, by tightening the gland nutRepacks the gland or replaces the valve
The nut joining the valve to the radiatorThe seal on the radiator tail has failedYes, if confident draining the radiatorDrains, reseals the tail and remakes the joint
The nut where the pipe enters the valveA loose or damaged compression jointSometimes, with a small tighteningReplaces the olive or the joint
The bleed valveValve not closed, or its seal has failedYes, close it or fit a new bleed valveReplaces the bleed valve
The radiator panel or seamsInternal corrosion has eaten throughNo lasting fixReplaces the radiator
The pipe itself, before the valveCorrosion, damage or a failed jointNoIsolates and repairs the pipe

Fixing a leaking valve spindle

If water gathers under the valve head, the seal round the spindle (the gland) has worn. This is very common on older valves.

  1. Take off the valve head or cap. On a thermostatic valve, the head usually unscrews or unclips from the body.
  2. Find the small nut round the spindle, just above the valve body. This is the gland nut.
  3. Hold the valve body steady with one spanner so it does not twist on the pipe.
  4. Turn the gland nut clockwise a quarter turn with a second spanner.
  5. Dry it and check. If it still weeps, try another small fraction of a turn. Do not overtighten, as the spindle can seize.

If it still leaks, the gland needs repacking or the valve needs replacing. On many modern valves, the easier answer is a new valve.

Fixing a leak where the valve meets the radiator

The valve connects to the radiator through a short threaded piece called a tail. If the seal on that thread fails, water weeps round the large nut.

  1. First try a small tightening of the nut, holding the valve body with a second spanner so you do not strain the pipe. Stop if it does not help.
  2. If it still leaks, isolate the radiator by closing both valves.
  3. Put a tray under the joint, undo the nut and let the radiator drain. Open the bleed valve to let air in so it drains faster. There will be a lot of water, often black.
  4. Unscrew the tail from the radiator, clean the threads, wrap them with PTFE tape or a suitable jointing compound, and screw the tail back in firmly.
  5. Remake the nut, open the valves (the lockshield to its original position), bleed the radiator and check for drips. Then top up the boiler pressure.

Our guide on how to bleed a radiator covers the bleeding step. If you are not comfortable draining a radiator, this is a quick job for an engineer.

Fixing a compression joint on the pipe

Where the pipe goes into the bottom of the valve, the joint is held by a nut and a brass ring called an olive. A small tightening, with the valve body held steady, often stops a weep. If the olive is damaged or the pipe is corroded, the joint needs remaking with a new olive, which means draining down the pipework. That is usually a job for an engineer.

A leaking radiator body

If the leak is from the panel itself, you will often see a rust spot, a bubble in the paint or a damp patch along a seam. That means the steel is corroding from the inside. Leak sealer products and putty can slow a pinhole down temporarily, but the radiator is failing and needs replacing.

A radiator rotting from inside also tells you something about the system: the water is probably low on inhibitor and full of sludge. If other radiators are cold at the bottom or you get black water when bleeding them, read our guide to a radiator not heating up, and consider a power flush when the new radiator goes on.

Be careful with leak sealers and heat

  • Some sealers added to the heating water can settle in the boiler or a magnetic filter. Check with your boiler manufacturer’s advice before adding one, and never use one as a permanent fix for a failing radiator.
  • Do not use a blowtorch or heat gun near a leaking radiator or its valves.
  • If water is near sockets, lights or electrical appliances, switch the power off at the consumer unit before touching anything.
  • Never remove the boiler casing. If the pressure keeps dropping and you cannot see a leak, call a Gas Safe registered engineer.

Hidden leaks and a boiler losing pressure

If your boiler keeps losing pressure but you cannot find a leak at any radiator, the water may be escaping under a floor, inside a wall or through the boiler’s pressure relief valve. Our guide to a boiler that keeps losing pressure explains how to narrow it down. Topping up pressure again and again brings fresh water into the system, which adds oxygen and speeds up corrosion, so it is worth finding the cause.

Repair or replace?

  • Repair if the leak is at a valve, joint or bleed valve and the radiator is otherwise sound.
  • Replace the valve if the gland keeps weeping, the valve will not close or it is seized.
  • Replace the radiator if it is leaking from the body, has several rust spots, or is old and undersized for the room anyway.

What it costs with Vantage

Most radiator leaks are small, quick repairs. In normal working hours there is no call-out fee. After the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive. Our work carries a 12 month labour guarantee.

Frequently asked questions

Is a leaking radiator an emergency?

A slow drip is not usually an emergency if you catch the water and isolate the radiator. A steady flow, a leak near electrics, or a boiler that keeps losing pressure is more urgent. Our phone is answered 24 hours a day if you need help straight away.

Can I still use my heating with a leaking radiator?

Usually yes, once you have closed both valves on the leaking radiator. Keep an eye on the boiler pressure. If the leak is from a pipe or the valves will not close, turn the heating off.

Why is my radiator leaking brown or black water?

Radiator water is dark because of sludge and corrosion inside the system. It is not harmful to touch, but it stains, so mop it up quickly. Dark water is a sign the system would benefit from a clean and fresh inhibitor.

Can I tighten a radiator valve to stop a leak?

Often, yes. A quarter turn on the gland nut under the valve cap, or on the joint nut with the valve held steady, can stop a weep. Do not keep tightening if it does not help, as you can damage the valve or the olive.

Do I need to drain the whole system to fix a leaking radiator?

Not usually. If both radiator valves close properly, you can drain just that radiator. If the valves do not seal, or the leak is on the pipe below the valve, the system may need partly draining.

When to call an engineer

If you cannot find the leak, the valves will not close, the radiator body is weeping or your boiler pressure keeps falling, it is time for a professional. Our central heating repairs team covers Hertfordshire, Bedfordshire and Cambridgeshire. Call 01462 506374, answered 24 hours a day, 7 days a week.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.