Skip to main content

Vantage Plumbing and Heating

Vaillant F02 Fault Code: Hot Water Sensor Fault Explained

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

Vaillant F02 (shown as F.02, or F.2 on older models) means the boiler has lost the signal from one of its hot water temperature sensors, an open circuit in the sensor or its wiring. Which sensor depends on the model, so the first step is to identify your boiler, and the fix is a sensor, plug or wiring repair carried out by a Gas Safe registered engineer.

In short

  • F02 is a sensor “interruption”: the circuit board is getting no usable signal from a hot water temperature sensor.
  • On ecoTEC plus boilers with a built-in actoSTOR hot water store, Vaillant lists F.02 as an interruption in the actoSTOR cylinder charging sensor, shown only together with F.91.
  • On Vaillant’s older atmoTEC combi boilers, F.2 means an interruption in the hot water outlet sensor.
  • F02 is not a flow sensor fault. On Vaillant boilers that is F.00.
  • You can reset once or twice and note the model. The sensor, plugs and wiring need an engineer.
Vaillant boiler installed by Vantage with neatly run copper pipework
A Vaillant boiler we installed, with the copper pipework run neatly below it.

New boiler?

Get an instant estimate for a new boiler

Answer a few questions about your home online and see your estimate straight away, fitted by our own engineers.

Instant boiler estimateOr call 01462 506 374

What F02 means on a Vaillant boiler

Vaillant boilers use NTC thermistors to measure temperature. An NTC is a small sensor whose resistance falls as it gets warmer, and the circuit board reads that resistance as a temperature. When the board sees an open circuit, where the resistance is effectively infinite, it cannot trust the reading and it raises an interruption code.

The flow and return sensors on the heating side have their own codes (F.00 and F.01). F02 belongs to the hot water side, and this is where the model matters.

Vaillant modelWhat F.02 or F.2 means (from Vaillant’s manuals)What it affects
ecoTEC plus with actoSTOR (VUI store models)Interruption in the actoSTOR cylinder charging sensor, only in combination with F.91The built-in hot water store and its charging
atmoTEC combi (VCW)Interruption in the hot water outlet sensorHot water temperature control
Standard ecoTEC plus combi or system boilerF.02 relates to the actoSTOR module, so it is not expected on models without oneCheck the model and exact code carefully

On the ecoTEC plus, Vaillant’s installation manual describes F.02 as “Interruption cylinder charging sensor actoSTOR (NTC) only in combination with F.91”. The actoSTOR is a hot water store with its own electronics built into certain ecoTEC plus models. The causes Vaillant lists are a faulty sensor, a faulty sensor cable, a bad plug connection at the sensor or a bad plug connection at the actoSTOR electronics.

On the atmoTEC range, an older line of open-flued Vaillant boilers, the installation manual lists F.2 as “Interruption: DHW outlet sensor”. DHW means domestic hot water, so this is the sensor that tells the boiler how hot the water leaving it for your taps is.

You may read elsewhere that F02 is a flow sensor fault. That does not match Vaillant’s manuals, which give the flow sensor interruption its own code, F.00. If you are unsure which model you have, the model name is usually shown on the front of the boiler, and your engineer can read the full type (for example VUI or VUW) from the data plate.

Newer Vaillant controls show codes with three digits, such as F.022 instead of F.22. If yours shows a three-digit code, give the engineer the exact code rather than assuming it matches this page.

Check these first

  1. Note the exact code and any others. On an actoSTOR model, F.02 should appear with F.91. Write down both, and the model name from the front of the boiler.
  2. Reset the boiler once. Press the reset button and let the boiler restart. If the code comes back, one more reset at most, then stop.
  3. Check the power. Make sure the fused spur by the boiler is on and the display is lit.
  4. Check heating and hot water separately. Note whether you still have heating, hot water, both or neither. It tells the engineer where to start.
  5. Look for leaks outside the casing. Water dripping onto the boiler or around the hot water store can reach connectors. Do not open anything, just note what you can see.
  6. Think about recent work. A recent service or repair can leave a plug partly disconnected.

If the code returns, book a Vaillant boiler repair with the model and the codes to hand.

What not to do

  • Do not remove the boiler casing or the store cover to look at sensors or plugs. Under the Gas Safety (Installation and Use) Regulations 1998 only a Gas Safe registered engineer may work on a gas appliance.
  • Do not keep resetting. A broken sensor circuit will not repair itself.
  • Do not turn the hot water temperature to maximum to “test” it. With a sensor out of action, the boiler cannot control the temperature properly.
  • If you smell gas, call the National Gas Emergency Service on 0800 111 999, open windows, do not use electrical switches and turn off the gas at the meter if it is safe.

Common causes of F02

CauseWhat you might noticeCan you fix it yourself?What the engineer does
Failed hot water sensorCode returns straight after a resetNoMeasures the sensor’s resistance and replaces it
Damaged sensor cableCode may come and go if the cable movesNoTests continuity and repairs or replaces the cable
Loose plug at the sensorCode after a service or repairNoReseats and inspects the connector
Loose plug at the actoSTOR electronicsF.02 with F.91 on a store modelNoChecks the connections on the actoSTOR board
Water or corrosion on a connectorCode after a leak near the boiler or storeOnly by stopping an external leakCleans or replaces the connector, fixes the leak
Control electronics faultSensor and wiring all test correctlyNoTests the board or module before replacing anything

What an engineer will check

  1. Identify the model and read the fault history. The engineer confirms which boiler you have and looks at the fault list, so they know which sensor F02 refers to.
  2. Inspect the sensor and its plugs. With the power isolated, they check the sensor is fitted properly and that the plugs at both ends are seated and clean.
  3. Measure the sensor. Resistance is measured and compared with what Vaillant expects at that temperature. An open circuit or a reading far out of range means the sensor has failed.
  4. Test the cable. Each core is tested for continuity along its length, looking for breaks, chafing or a pin that has pushed back.
  5. Check the electronics last. On an actoSTOR model, the store’s electronics and its connection to the main board are checked. The circuit board is only replaced once everything else is proven good.
  6. Run the hot water. After the repair, the engineer runs hot water and checks the temperature reading is sensible and stable.

Repair or replace?

A hot water sensor fault is almost always worth repairing. Sensors are small parts and wiring repairs are quick. Replacement is only worth discussing if the electronics have failed on an older boiler that already has other problems. Our repair or replace guide sets out how we make that call honestly.

If you are losing hot water but the heating works and there is no code at all, our guide to no hot water but the heating works covers the other common causes.

What it costs with Vantage

In normal working hours there is no call-out fee. Gas faults start with a fixed-price Gas Safe diagnostic visit, and if we can fix it on the same visit, part of that diagnostic charge comes off the repair. After the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive. Our work comes with a 12 month labour guarantee.

Related Vaillant codes

  • Vaillant F20: the overheat safety cut-out has operated.
  • Vaillant F23: the temperature difference between flow and return is too great.
  • Vaillant F22: low water pressure in the heating system.

Frequently asked questions

Is Vaillant F02 a flow sensor fault?

No. In Vaillant’s manuals the flow sensor interruption is F.00. F02 relates to a hot water sensor: the actoSTOR cylinder charging sensor on ecoTEC plus store models, or the hot water outlet sensor on older atmoTEC combis.

What is F.91 and why does it appear with F02?

On ecoTEC plus models with an actoSTOR store, Vaillant’s manual says F.02 is shown only in combination with F.91. Together they point the engineer at the actoSTOR side of the boiler, its sensors and connections, rather than at the main heating sensors.

Can I still use my heating with an F02 code?

It depends on the model and how the boiler responds, so try the heating and note what happens. Either way, the boiler is protecting itself, and a sensor fault like this should be repaired rather than lived with.

My boiler shows F02 but I do not have an actoSTOR. What now?

Write down the exact code, including any dot and how many digits it has, and the model name. Codes can be misread on small displays, and newer boilers use three-digit codes. An engineer can read the fault list and confirm what the boiler is really reporting.

When to call an engineer

If F02 returns after a reset or two, a Gas Safe registered engineer needs to test the sensor and its wiring. We repair and service Vaillant boilers across Hertfordshire, Bedfordshire and Cambridgeshire, and our phone is answered 24 hours a day, 7 days a week. Book a boiler repair or call 01462 506374.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.