Boiler Efficiency Ratings Explained: ErP, A-Rated and Condensing
Hertfordshire, Bedfordshire & Cambridgeshire
Boiler efficiency is the share of the energy in the gas that ends up as useful heat in your home, and a modern condensing gas boiler is rated at over 90 per cent on the ErP scale, which is an A rating. Older non-condensing boilers often ran in the 70s or low 80s per cent, so replacing one makes a real difference, but how efficiently any boiler runs day to day depends heavily on its flow temperature, controls and the condition of your heating system.
- Efficiency is useful heat out divided by energy in. The rest is lost, mostly up the flue.
- Boilers are rated on the ErP scale. Class A means a seasonal efficiency of 90 per cent or more, up to 98 per cent.
- In England, every gas boiler fitted in an existing home must be at least 92 per cent ErP efficient under the Boiler Plus rules.
- Condensing boilers recover extra heat from the flue gases, but only when the water returning to the boiler is cool enough, around 55 degrees or lower.
- Lower flow temperatures, good controls, a clean system and yearly servicing keep a boiler near its rated efficiency.

What boiler efficiency actually means
When gas burns in a boiler, the heat is passed through a heat exchanger into the water that flows round your radiators and, on a combi, into your hot taps. Some heat is always lost, mainly in the hot exhaust gases leaving through the flue and a little from the boiler casing.
Efficiency is simply how much of the energy you pay for becomes heat you can use. A boiler rated at 92 per cent turns 92 units of gas energy into useful heat for every 100 units it burns. The higher the figure, the less gas you need for the same warmth.
How boiler efficiency is rated
ErP ratings (the current system)
Since 2015, boilers sold in the UK have carried an energy label under the ErP (Energy-related Products) rules. The label shows a letter class based on the boiler’s seasonal space heating efficiency, a figure that reflects how the boiler performs across a typical heating season rather than at one ideal test point.
| ErP class | Seasonal space heating efficiency |
|---|---|
| A+++ | 150 per cent or more |
| A++ | 125 to under 150 per cent |
| A+ | 98 to under 125 per cent |
| A | 90 to under 98 per cent |
| B | 82 to under 90 per cent |
| C | 75 to under 82 per cent |
| D | 36 to under 75 per cent |
Figures above 100 per cent are not possible for a boiler burning gas. The A+ classes and above exist for heat pumps, which move heat from the outside air or ground and so deliver more heat than the electricity they use. A gas boiler on its own tops out at class A, which is why nearly every new gas boiler is described as A-rated.
A combi boiler label also shows a separate water heating efficiency class, which covers how well it heats hot water for your taps.
Package labels
Installers can produce a package label that combines the boiler with its controls and, where fitted, solar or other extras. Qualifying controls, such as weather compensation or smart thermostats with modulation, can lift the package rating slightly above the boiler alone. That is one reason good controls matter.
SEDBUK (the older system)
Before ErP, UK boilers were rated under SEDBUK, which gave a seasonal efficiency percentage. You may still see a SEDBUK figure on older boilers and paperwork. The two systems are calculated differently, so a SEDBUK percentage and an ErP percentage for the same boiler will not match exactly.
Gross and net figures
Some brochures, particularly from continental Europe, quote efficiencies above 100 per cent. Those figures use a net calorific value, which ignores the heat locked up in water vapour. UK ErP figures use the gross value, which is the fairer comparison. Always compare like with like.
The legal minimum in England
Since April 2018, the Boiler Plus standard has required every gas boiler installed in an existing home in England to have an ErP efficiency of at least 92 per cent. It also requires time and temperature controls, and a combi must have one extra energy saving measure: flue gas heat recovery, load compensation, weather compensation, or a smart thermostat with automation and optimisation. If you are having a new boiler fitted, our boiler installation team specifies the controls as part of the quote.
Why condensing matters
A condensing boiler has a larger heat exchanger that cools the flue gases enough for the water vapour in them to condense. Condensing releases extra heat, which the boiler puts back into the heating water. The condensed water is drained away through the plastic condensate pipe you see near most modern boilers.
The catch is temperature. Natural gas flue gases start to condense when the water returning to the boiler is at about 55 degrees or lower. If the boiler is set to send water out to the radiators very hot, the return water may be too warm for the boiler to condense much, and it runs below its rated efficiency.
That is why a boiler’s real-world efficiency depends on how it is set up:
- Flow temperature. Many combis are left at a high radiator setting all year. Turning it down so the return water stays cooler helps it condense more. On a combi this does not affect the hot water temperature at your taps.
- Weather compensation. An outside sensor lowers the flow temperature automatically on milder days.
- Load compensation. The thermostat tells the boiler how much heat is needed, so it modulates instead of switching fully on and off.
- Correct sizing. An oversized boiler cycles on and off in mild weather, which wastes gas.
If you have a hot water cylinder, do not simply turn everything down. Stored hot water needs to reach around 60 degrees to control the risk of legionella, so the setup needs more care.
What drags a boiler’s efficiency down
| Problem | What happens | The fix |
|---|---|---|
| Sludge (magnetite) in the system | Radiators cold at the bottom, heat exchanger partly blocked | System clean or power flushing, then a magnetic filter |
| Limescale in the heat exchanger | Poor heat transfer, noise, overheating | Descale, scale protection on combi mains supply |
| Air in radiators | Cold patches, boiler works harder | Bleed the radiators |
| High flow temperature | Boiler rarely condenses | Set flow temperature to suit the radiators |
| Poor or missing controls | Heating runs when not needed | Programmer, room thermostat, TRVs, or smart controls |
| No yearly service | Burner and heat exchanger not cleaned, combustion not checked | Annual service by a Gas Safe engineer |
A proper boiler service includes a combustion check with a flue gas analyser, which tells the engineer how cleanly and efficiently the boiler is burning.
How to tell if your boiler is condensing
Signs you have a condensing boiler:
- A plastic flue, usually white.
- A plastic condensate pipe leading from the boiler to a drain.
- A plume of vapour from the flue in cold weather.
- Fitted since about 2005, when gas boilers in England and Wales became condensing as standard.
If your boiler has none of these, it is probably non-condensing and well below modern efficiency.
Adjust only what the user guide allows
- You can change the heating flow temperature using the boiler’s own controls if the user guide explains how.
- Never remove the boiler casing or adjust gas settings. Only a Gas Safe registered engineer can work inside a gas boiler.
- If you smell gas, call the National Gas Emergency Service on 0800 111 999, open windows and turn off the gas at the meter if it is safe to do so.
How we price it
Installations are quoted as a fixed price after a free survey, so the price you agree is the price you pay. You can get your price online in a couple of minutes with our boiler quote tool. Servicing and repairs are charged at the rates published on our prices page, so you know what you will pay before we arrive.
Frequently asked questions
What is a good efficiency rating for a boiler?
Any new gas boiler fitted in an existing home in England must be at least 92 per cent ErP efficient, which is class A. Most modern condensing boilers are rated a little above that, so the differences between good boilers are small.
Does an A-rated boiler save money?
Compared with an old non-condensing boiler, yes, because more of the gas you buy ends up as heat. Compared with another A-rated boiler, the savings depend more on how it is set up and controlled than on the rating.
How do I make my boiler more efficient?
Keep it serviced every year, keep the system clean and protected by a filter, bleed radiators when needed, use good controls and set the flow temperature to suit your radiators. A well-set-up boiler condenses more of the time.
Why is my boiler efficiency figure over 100 per cent?
That figure has been calculated on a net calorific basis, which leaves out the heat in the water vapour. UK ErP ratings use a gross basis, so a condensing gas boiler will show just over 90 per cent.
Does boiler efficiency drop with age?
It can. Sludge, scale, worn parts and missed services all reduce how efficiently a boiler runs. Yearly servicing and a clean system help it stay close to its rated efficiency for longer.
Efficient heating in Hertfordshire, Bedfordshire and Cambridgeshire
Whether you want your current boiler set up to run more efficiently or a new A-rated boiler fitted, our Gas Safe registered engineers can help. See our boiler installation page or call 01462 506374. The phone is answered 24 hours a day, 7 days a week.
What our customers say
Speak to a local engineer
Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.
Gas Safe registered, number 956889. Emergency line answered 24/7.
Boiler engineers near you
Boiler playing up? Book a local Gas Safe engineer
We cover Hertfordshire, Bedfordshire and Cambridgeshire. Choose your town:
Not listed? See all the areas we cover or call 01462 506 374