Skip to main content

Vantage Plumbing and Heating

How Does a Combi Boiler Work? A Plain English Guide

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

A combi boiler heats your radiators and your hot water from one compact unit, with no hot water cylinder or tanks in the loft. It heats water for the radiators in a sealed loop, and when you turn on a hot tap it switches over to heat fresh mains water instantly as it flows through, so you get hot water on demand at mains pressure.

  • “Combi” is short for combination: one boiler for both heating and hot water.
  • Hot water is heated as you use it, straight from the cold mains, so there is no stored hot water to run out.
  • A diverter valve inside the boiler switches the heat between the radiators and the taps. Hot water always takes priority.
  • How much hot water you get depends on the boiler’s output and your mains water flow.
  • Combis suit most homes with one main bathroom. Homes where several showers run at once usually do better with a cylinder.
Ideal boiler installed by Vantage in a fitted cupboard, with copper pipework and a magnetic system filter
One of our boiler installations: an Ideal combi in a fitted cupboard with a magnetic system filter.

How a combi boiler works, step by step

A combi has two jobs, and it does one at a time. Understanding this makes it much easier to choose the right boiler when you are planning a boiler installation.

When the heating is on

  1. Your thermostat or programmer asks for heat.
  2. The fan starts, the gas valve opens and the burner lights.
  3. The flame heats the water in the main heat exchanger.
  4. The pump pushes that hot water around the heating circuit, through the radiators and back to the boiler.
  5. The boiler adjusts its flame (modulates) to hold the temperature you have set, and switches off when the thermostat is satisfied.

The heating side is a sealed loop. The same water goes round and round, which is why the system has a pressure gauge and an expansion vessel.

When you turn on a hot tap

  1. A flow sensor inside the boiler detects water moving through the cold mains inlet.
  2. The diverter valve switches over, sending the hot water from the main heat exchanger through a second, smaller heat exchanger instead of to the radiators.
  3. That second heat exchanger (usually a plate heat exchanger) passes the heat to the fresh mains water flowing through it.
  4. Hot water arrives at your tap at mains pressure.
  5. When you turn the tap off, the diverter valve switches back and the heating carries on.

Because the boiler can only send heat one way at a time, the radiators pause briefly while you run a bath or shower. In a well-insulated home you rarely notice.

The main parts of a combi boiler

PartWhat it does
Gas valve and burnerControl the gas and burn it to make heat
FanBrings in air for burning and pushes waste gases out of the flue
Main heat exchangerWhere the flame’s heat passes into the water
Plate heat exchangerTransfers heat from the boiler water to the fresh mains water for your taps
Diverter valveSwitches the heat between the heating circuit and the hot water side
Flow sensorTells the boiler a hot tap has been opened
PumpMoves water around the boiler and the radiators
Expansion vesselAbsorbs the water’s expansion as it heats, so the pressure stays steady
Printed circuit board (PCB)The boiler’s control electronics
Condensate trap and pipeDrain away the water produced by a condensing boiler
Pressure gauge and filling loopShow and top up the heating system pressure

Why modern combis are condensing boilers

All new gas boilers fitted in homes today are condensing boilers. As well as the heat from the flame, they recover extra heat from the water vapour in the flue gases, which is why they are so efficient. New gas boilers fitted in existing homes in England must be at least 92% ErP efficient under the Boiler Plus rules.

That recovered water vapour turns into condensate, a mildly acidic water that drains away through a plastic pipe. If that pipe runs outside, it can freeze in very cold weather and stop the boiler. Our guide to a frozen condensate pipe shows how to deal with it safely.

How much hot water can a combi give?

A combi does not store hot water, so the question is not how much, but how fast. Manufacturers quote a hot water flow rate in litres per minute at a 35 degree temperature rise, which is roughly the rise needed to take cold mains water to a comfortable shower temperature. The higher the boiler’s output in kW, the higher the flow rate. For example, Ideal quotes these figures for its Logic Max combi range:

ModelHot water flow rate at a 35 degree rise
Logic Max Combi 249.9 litres per minute
Logic Max Combi 3012.4 litres per minute
Logic Max Combi 3514.5 litres per minute

Two other things limit what you actually get:

  • Your mains water flow. A combi cannot deliver more hot water than your incoming mains supplies. If your mains flow is weak, a bigger boiler will not help.
  • The temperature of the mains water. In winter the cold water coming in is colder, so the boiler has to raise it further and the flow at a given temperature drops a little.

This is why a surveyor measures your mains flow rate, not just the pressure, before recommending a combi. Our guide to the best combi boilers compares the models we recommend.

Advantages and disadvantages of a combi

AdvantagesDisadvantages
Hot water on demand, with no waiting for a cylinder to heatHot water flow is shared, so two showers at once can struggle
No cylinder or loft tanks, which frees up spaceDepends on good mains water flow and pressure
Mains pressure hot water for stronger showersIf the boiler breaks down you lose heating and hot water together
Only heats the water you useNo immersion heater backup
Fewer parts outside the boiler and simpler pipeworkIn hard water, the plate heat exchanger needs scale protection

Is a combi right for your home?

A combi is usually a good fit if:

  • You have one main bathroom, or a bathroom and an en suite that are rarely used at the same time.
  • Your mains water flow and pressure are good.
  • You want to free up the space taken by a cylinder or loft tanks.

A system boiler with an unvented cylinder is usually better if:

  • You have two or more bathrooms that are often in use at the same time.
  • Your household uses a lot of hot water at peak times.
  • Your mains flow is not strong enough for a combi.

If you are switching from a system with a cylinder to a combi, the installer needs to check your mains flow, and the pipework to the taps may need changes. Our boiler installation surveys cover all of this.

Common combi boiler problems

Knowing how a combi works makes its common faults easier to understand.

  • Low pressure on the heating side stops the boiler. Topping up with the filling loop, if your user guide allows, often fixes it.
  • A stuck diverter valve can leave you with hot water but no heating, or heating that comes on when you run a tap.
  • A scaled plate heat exchanger causes lukewarm or fluctuating hot water, which is common in hard water areas like Hertfordshire.
  • A faulty flow sensor means the boiler does not notice you have turned on a tap. Our guide to no hot water but the heating works covers this.
  • A frozen condensate pipe stops the boiler in freezing weather.

Leave the inside to an engineer Everything inside the boiler casing, including the diverter valve, plate heat exchanger, gas valve, fan and PCB, must only be worked on by a Gas Safe registered engineer. You can safely check the pressure, top up with the filling loop if your user guide allows, check the controls and reset the boiler a small number of times. If you smell gas, call 0800 111 999.

Controls you need with a new combi

In England, a new gas combi must be fitted with time and temperature controls, plus at least one extra energy-saving measure. The options are smart controls with automation and optimisation, weather compensation, load compensation or flue gas heat recovery. Most homeowners choose a smart thermostat.

How we price it

Installations are quoted as a fixed price after a free survey, so the price you agree is the price you pay. You can get your price online in a couple of minutes with our boiler quote tool. Our other rates are published on our prices page. New boiler packages include a magnetic system filter, the first year’s service and removal of the old boiler.

Frequently asked questions

Do I need a water tank with a combi boiler?

No. A combi heats water straight from the cold mains, so there is no hot water cylinder and no cold water tank in the loft. That is one of the main reasons people choose one.

Is there always hot water with a combi boiler?

Yes, as long as the boiler is working, because it heats water as you use it rather than from a store. The limit is flow rate: if several hot taps or showers run at once, each gets less.

Can a combi boiler run two showers at once?

It can, but the hot water flow is shared between them, so both will be weaker. Homes where two showers regularly run together are usually better with a system boiler and an unvented cylinder.

Why do my radiators cool down when I run the hot tap?

A combi can only send heat one way at a time, and hot water takes priority. While the tap runs, the diverter valve sends the heat to the hot water side, then switches back to the heating when you turn it off.

What size combi boiler do I need?

It depends on your hot water demand and your mains flow more than the number of radiators. An installer should measure your mains flow and look at your bathrooms before recommending a size.

Help choosing a combi in Hertfordshire

If you are thinking about a new combi or switching from a cylinder, we will survey your home, check your mains flow and recommend the right boiler. We are Gas Safe registered (956889), Ideal Max accredited and Vaillant myREWARDS installers. See our boiler installation page or call 01462 506374.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.