Skip to main content

Vantage Plumbing and Heating

How to Check for a Bathroom Leak: A Step-by-Step Guide

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

To check for a bathroom leak, look for the signs first (stains on the ceiling below, damp or lifting flooring, loose tiles, a musty smell), then test each fitting in turn: the toilet, the shower, the bath, the basin and the pipes you can see. A simple water meter test tells you whether water is escaping from the supply pipes at all, and most bathroom leaks can be narrowed down in an afternoon without lifting a single tile.

  • Common signs are a stain on the ceiling below, soft or stained flooring, loose or cracked tiles, failing silicone, a musty smell and a higher water bill.
  • A water meter test shows whether supply water is escaping when nothing is running.
  • The toilet paper test finds a leaking toilet valve, one of the most common hidden leaks.
  • Run the shower, bath and basin one at a time to see which one makes the stain or damp worse.
  • A leak that only appears when the shower is used is often the tray seal, the silicone or the grout, not a pipe.
  • Hidden pipe leaks under floors or behind walls need proper leak detection equipment.
Thermal imaging camera screen used by Vantage for leak detection
Thermal imaging lets us trace a hidden leak without lifting floors.

Signs you have a bathroom leak

Bathroom leaks are rarely dramatic. Most are slow drips that show up somewhere else first, often the room below. Look for:

  • A stain or bubbling paint on the ceiling below the bathroom, often under the shower, bath or toilet.
  • Damp, soft or lifting flooring, especially vinyl or laminate that is curling at the edges, or boards that give underfoot near the toilet or bath.
  • Loose, cracked or hollow sounding tiles, and grout that is dark, crumbling or missing.
  • Black mould or failing silicone along the edge of the bath or shower tray.
  • A musty smell that does not go away when the room is aired.
  • Water in the wrong place: a puddle behind the toilet, drips inside the vanity unit, or water on the floor after every shower.
  • A rising water bill with no change in how you use water, or water pressure that seems to have dropped.

If water is coming through a ceiling near a light fitting, switch off that lighting circuit at the consumer unit and keep people away from it before you do anything else.

Step 1: Do the water meter test

If you have a water meter, this is the quickest way to tell whether water is escaping from your supply pipes. Water companies recommend a version of this test:

  1. Turn off every tap, and make sure the washing machine, dishwasher, toilets and anything else that uses water are not filling.
  2. Read the meter and write down the number, or take a photo.
  3. Wait at least 30 minutes without using any water.
  4. Read the meter again.

If the reading has moved, water is going somewhere. You can narrow it down by closing the internal stop tap and repeating the test: if the meter still moves with the stop tap closed, the leak is on the supply pipe between the meter and your stop tap, rather than inside the house. If it stops moving, the leak is somewhere inside, and the bathroom is a good place to start.

If the meter moves and you cannot find any sign of water in the bathroom or anywhere else, that is the point to call in professional leak detection rather than lifting floors to look.

Bear in mind a meter test only catches leaks on pressurised pipework. Water escaping from a waste pipe, a shower tray seal or failed grout only leaks when that fitting is being used, so the meter will not show it.

Step 2: Check the toilet

A toilet with a worn fill valve or flush valve can let water trickle into the pan all day. Water companies estimate that around 1 in 20 toilets in the UK leaks, and even a small trickle wastes a surprising amount of water. It does not damage the house, but it shows up on a metered bill.

The toilet paper test:

  1. Flush the toilet and wait about 30 minutes for everything to settle.
  2. Dry the back of the pan with toilet paper.
  3. Stick a fresh, dry sheet to the back of the pan.
  4. Leave it for at least three hours, ideally overnight, without flushing.

If the paper is wet or torn, water is running into the pan and the cistern valve needs attention. Our guide on how to fix a running toilet explains the usual causes.

Leaks onto the floor are different. Check:

  • The water supply pipe and isolating valve behind the toilet for drips.
  • Where the cistern joins the pan, on close coupled toilets.
  • The base of the toilet for water after flushing, which can mean the pan connector to the soil pipe has failed or come loose.

Water at the base of the toilet is more serious, because it can soak into the floor. Stop using that toilet until it is checked.

Step 3: Check the shower

Showers cause more hidden damage than any other fitting because the leak only happens when the shower is running, and the water often travels along a joist before it appears.

  1. Look at the silicone around the tray or bath. Any gap, lifting edge or black mould can let water behind the tray.
  2. Check the grout and tiles in the shower area. Cracked grout lets water through to the wall behind, especially on plasterboard.
  3. Test the tray and waste separately. With the shower head held low into the waste, run water for a few minutes without wetting the walls. If a stain or drip appears below, suspect the waste or trap. If it only leaks when the walls get wet, suspect the silicone, grout or screen seals.
  4. Check the screen or door. Water escaping past the seals onto the floor can soak into the floor edge.
  5. Check the shower valve if you have access. Drips from behind the valve or a concealed valve access panel need a plumber.

Step 4: Check the bath and basin

  • Bath: Fill the bath partly and let it drain while someone watches below, or lift the bath panel with a torch and look at the waste, overflow and tap connections. An overflow seal that only leaks when the bath is filled high is very common.
  • Basin: Open the vanity unit and look at the waste, trap and the flexible tap connectors. Run the tap and hold tissue around each joint. Flexible hoses can weep at the crimp long before they fail.
  • Silicone: Check the joint between the bath and wall. When you sit in a bath it drops slightly, and a joint that looks fine when the bath is empty can open up. Our guide on how to seal a bath covers resealing.

Step 5: Check the pipes you can see

Look along any exposed pipes, under the basin, behind the toilet and in the airing cupboard if it backs onto the bathroom. Check isolating valves, compression joints and the bottom of radiators or towel rails. A green or white crust on a joint means it has been weeping for a while.

Narrowing it down: what the symptom tells you

What you noticeMost likely sourceCan you fix it yourself?What a plumber does
Stain below only after showersSilicone, grout, tray seal or wasteResealing, sometimesIsolates the fault, replaces the waste or seal, regrouts or retiles
Stain below that grows even when nothing is usedPressurised supply or heating pipeNoUses leak detection to find it with minimal damage
Water at the base of the toilet after flushingPan connector or cistern sealNo, in most casesReplaces the connector or seals
Paper test wet in the toilet panFill or flush valveSometimesReplaces the valve
Drips inside the vanity unitTap connector or wasteTightening a waste nut, sometimesReplaces the connector or trap
Meter moves with the stop tap closedUnderground supply pipeNoTraces the supply pipe leak

When you need leak detection

If the meter is moving but you cannot see any water, or the stain below keeps growing with nothing running, the leak is probably on a pipe buried in the floor, behind tiles or under a concrete slab. This is where professional leak detection saves money: acoustic listening, thermal imaging, moisture mapping and tracer gas can pinpoint the leak so only a small area needs opening. Our article on leak detection technology explains how each method works.

Stay safe while you look

  • If water is near a light fitting, switch off that circuit at the consumer unit and do not touch wet switches or sockets.
  • If a ceiling is bulging with water, keep people out from under it.
  • Know where your stop tap is. Turning it off stops water flowing to the leak on the cold supply while you wait for help.
  • Do not keep using a shower or toilet you suspect is leaking. Every use adds water to the floor or ceiling.

What it costs with Vantage

In normal working hours there is no call-out fee. After the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Frequently asked questions

How do I know if my shower is leaking behind the tiles?

Look for loose or hollow tiles, cracked grout, mould in the grout lines and a stain or damp patch on the other side of the wall or on the ceiling below that appears after showers. If the leak only happens when the walls get wet, it is usually the grout or seals rather than a pipe.

Can a bathroom leak come through the ceiling below?

Yes, and that is often the first sign. Water runs along joists and pipes before it drips, so the stain may not be directly below the fitting that is leaking. Test each fitting in turn to find which one makes the stain worse.

Is a leaking toilet an emergency?

Water running into the pan is not an emergency, but it wastes water. Water leaking onto the floor from the base, pipes or cistern should be dealt with quickly, because it can soak into the floor and ceiling below. Turn off the toilet’s isolating valve if there is one.

Does home insurance cover a bathroom leak?

It depends on your policy. Many policies cover damage from a sudden escape of water but exclude gradual leaks and failed sealant or grout. Check your policy wording and speak to your insurer before starting repairs.

Who can find a hidden leak without ripping up the bathroom?

A plumbing company with proper leak detection equipment can usually pinpoint a hidden leak with little or no damage. Our guide on choosing a leak detection company explains what to ask.

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Leak help in Hertfordshire, Bedfordshire and Cambridgeshire

If you have found signs of a leak but cannot pin down the source, our engineers can trace it and repair it. See our leak detection service or call 01462 506374, answered 24 hours a day, 7 days a week, with emergency cover if water is coming through a ceiling.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.