Skip to main content

Vantage Plumbing and Heating

Installing an Outside Tap: What to Consider Before You Fit One

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

Installing an outside tap means teeing into the cold mains inside the house, fitting an isolating valve and a double check valve, running a pipe through the wall and mounting a garden tap at least 150 mm above the ground. It is a simple job for a plumber and usually needs no permission, but the water regulations do require backflow protection, and the pipe must be protected from frost, which is where most DIY installations fall short.

In short

  • Every outside tap should have a double check valve to stop garden water being drawn back into your drinking water.
  • Fit the check valve and an isolating valve inside the house, where they are protected from frost.
  • Put the tap where you actually need it, on a wall close to the cold mains, at least 150 mm above the ground.
  • A standard outside tap does not need planning permission or notifying to the water company. An automatic garden watering system does.
  • Each winter, turn it off inside, drain the tap and disconnect the hose.

Do you need permission to fit an outside tap?

For a normal garden tap on a house, no. You do not need planning permission, and WaterSafe, the national register of approved plumbers, does not list a standard outside tap among the works you must tell your water company about.

That changes for bigger jobs. Under the Water Supply (Water Fittings) Regulations 1999, you must notify your water supplier before installing a garden watering system that is not operated by hand, or a pond or swimming pool holding more than 10,000 litres. If you are planning irrigation or automatic filling as well as a tap, ask your plumber to deal with the notification.

What the regulations do require for every outside tap is protection for the drinking water supply, which is the most important part of the job.

Backflow protection: the part people miss

When you leave a hose lying in a paddling pool, a water butt or a bucket of soapy water, and the mains pressure drops (for example when a water main is repaired nearby), water can be siphoned back up the hose into your pipes. That is backflow, and it can contaminate the drinking water in your home and your neighbours’.

WaterSafe’s advice is clear: the water regulations specify that outside taps should always have a double check valve. A double check valve contains two one-way valves in series, so water can only flow out.

Current industry guidance is to fit that double check valve on the pipe inside the house, within the heated part of the building, where it is protected from frost, rather than relying on a check valve built into the tap outside. Older taps with check valves in the tap body were more vulnerable to freezing. If your existing tap has no check valve at all, one can be added to the supply pipe indoors.

A house garden is treated as a moderate risk, which the double check valve covers. If you plan to use hose-end feeders for fertiliser or weedkiller, fill a pond, or connect a pressure washer or irrigation system, the risk is higher and so is the level of protection needed. Mention it before the work starts. Our general plumbing team fits the right protection for how you plan to use the tap.

Where to put your outside tap

The best position is usually the one closest to both the cold mains and the place you will use it most.

LocationProsThings to watch
Back wall behind the kitchen sinkCold mains right there, short pipe runCheck for cavity wall insulation and cables in the wall
Utility room or cloakroom wallOften has its own cold supplySame checks on the wall
Front of the houseHandy for car washing and front gardensVisible to passers-by, so consider a lockable tap
End of the gardenSaves dragging a hoseNeeds a buried pipe, normally laid between 750 mm and 1,350 mm deep to protect it from frost and damage
Garage wallProtected pipe routeAn unheated garage can freeze, so insulate carefully

The regulations set a minimum height of 150 mm above ground for the outlet, which keeps it clear of puddles and soil. In practice most taps go a little higher, at a height where a watering can fits underneath.

Take the supply from the cold mains, not from a pipe fed by a tank in the loft. Mains pressure gives a useful flow at the hose, and a tank-fed supply is not drinking water and gives poor pressure.

What goes into an outside tap installation

A proper installation has more to it than a tap on a wall.

  1. A tee on the cold mains inside the house, made with a soldered or compression fitting.
  2. An isolating valve so the tap can be turned off from inside, ideally with a drain point so the outside section can be emptied in winter.
  3. A double check valve after the isolating valve, inside the heated space.
  4. A pipe through the wall, sleeved where it passes through the brickwork, and sealed on the outside.
  5. A wall plate elbow fixed firmly to the outside wall, so the tap does not twist when you turn it.
  6. The tap itself, with a hose connector.
  7. Insulation on any exposed pipework.

Some DIY kits use a self-cutting tee that clamps onto the pipe and pierces it. They can work, but a proper tee joint is more dependable, and a clamp that starts to weep inside a kitchen cupboard can go unnoticed for a long time.

Before you drill

  • Check the wall for hidden pipes and cables before drilling through it. A cable detector helps, but is not foolproof.
  • Turn off the water at the internal stop tap before cutting into the mains.
  • If your house has an older lead or unusual supply pipe, do not cut into it. Get a plumber to look first.
  • If you disturb pipework and water starts leaking inside a wall or floor, turn off the stop tap straight away.

Choosing the right tap

TypeBest forNotes
Standard brass bib tapMost gardensSimple and hard-wearing. Choose one with a hose union outlet
Quarter-turn lever tapQuick on and offEasier to use with wet or cold hands
Lockable tapFront gardens and rented homesStops the tap being used without permission
Hot and cold outside mixerWashing cars, dogs and muddy bootsNeeds a hot supply too, and both supplies need backflow protection
Frost-resistant tapExposed wallsThe valve sits inside the wall, where it stays warmer

Across most of Hertfordshire the water is hard, so limescale builds up on tap outlets and inside washers over time. A good quality brass tap copes better than a cheap one. If limescale is a problem throughout the house, our water softener installation page explains the options.

Protecting an outside tap in winter

A frozen outside tap can split the pipe inside the wall, and you may not find the leak until it thaws. Each autumn:

  1. Disconnect the hose. WaterSafe’s advice is to turn off the hosepipe at the tap and ideally disconnect it when not in use.
  2. Turn off the isolating valve inside the house.
  3. Open the outside tap and let the pipe drain. Use the drain point inside if there is one.
  4. Leave the tap open over winter so any water left has room to expand.
  5. Check the insulation on any exposed pipe, and fit an insulated tap cover if the wall faces north or east.

If a pipe does freeze and split, turn off the stop tap and get it repaired. A hidden leak inside a cavity wall can cause damp that spreads a long way. Our leak detection service finds leaks without opening up walls unnecessarily.

Common problems with existing outside taps

  • Dripping when closed: usually a worn washer or seat. A simple repair, or a new tap.
  • Weak flow: often a partly closed isolating valve, a blocked check valve, or low pressure in the whole house. Our guide to low water pressure in the whole house explains what a plumber checks.
  • Banging when the tap is shut off quickly: water hammer, especially on a quarter-turn tap. See our guide to banging pipes and water hammer.
  • Loose tap that twists on the wall: the wall plate has come away and needs refixing before the joint behind it leaks.

DIY or a plumber?

A confident DIYer can fit an outside tap. The risks are cutting into the mains without isolating it properly, leaving out the double check valve, running pipework where it will freeze, and fixing the tap so poorly that it moves every time it is used. A plumber will choose the right route, fit the valves inside, and leave you with a tap that works for years.

Our general plumbing repairs team fits and repairs outside taps across Hertfordshire, Bedfordshire and Cambridgeshire, and our vans are fully stocked with the fittings the job needs.

What it costs with Vantage

In normal working hours there is no call-out fee. Plumbing jobs like this are charged on time and parts: after the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive. Our work carries a 12 month labour guarantee.

Frequently asked questions

Does an outside tap need a double check valve?

Yes. WaterSafe says the water regulations specify that outside taps should always have a double check valve, to stop contaminated water being drawn back into the drinking water supply. It is best fitted inside the house, where it is protected from frost.

How high should an outside tap be?

The outlet should be at least 150 mm above the ground. Most people fit it a little higher so that a watering can or bucket fits underneath.

Can an outside tap freeze?

Yes. Turn it off at the isolating valve inside each autumn, drain the tap and leave it open, disconnect the hose and insulate any exposed pipe. A frost-resistant tap helps on exposed walls.

Can I have hot water to an outside tap?

Yes, with a hot and cold outside mixer tap. It needs a hot supply run through the wall as well, and both supplies need backflow protection. It is useful for washing cars, dogs and boots.

Will an outside tap increase my water bill?

Only by the water you use. If you have a water meter, everything that comes through the outside tap is metered like any other tap, so a hose left running or a slow drip adds up.

Plumbing help in Hertfordshire, Bedfordshire and Cambridgeshire

If you want an outside tap fitted properly, or an old one repaired, our plumbers can help. We are rated 4.9 on Google and our phone is answered 24 hours a day, 7 days a week. See our general plumbing repairs page or call 01462 506374.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.