Skip to main content

Vantage Plumbing and Heating

Types of Hot Water Cylinder Explained: Vented, Unvented and More

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

The two main types of hot water cylinder are vented cylinders, which are fed by a cold water tank in the loft and deliver hot water by gravity, and unvented cylinders, which are fed straight from the mains and deliver hot water at mains pressure. Within those, a cylinder can be direct (heated by an electric immersion) or indirect (heated by a boiler or heat pump through a coil), and there are specialist versions for solar panels, heat pumps, flats without a loft, and thermal stores.

In short

  • Vented cylinders need a cold water tank in the loft. Pressure depends on the height of that tank.
  • Unvented cylinders run at mains pressure with no loft tank, but need safety devices and a qualified installer.
  • Direct cylinders are heated by immersion elements. Indirect cylinders are heated by a boiler or heat pump through a coil.
  • Heat pump cylinders have a larger coil, and solar cylinders have a second coil for the solar panels.
  • If you have a combi boiler, you do not have a cylinder. Hot water is heated on demand.
Unvented hot water cylinder installed by Vantage
An unvented hot water cylinder we installed.

Vented vs unvented: the main choice

Vented cylinderUnvented cylinder
Water supplyCold water tank in the loftDirect from the mains
Hot water pressureDepends on the height of the loft tank, often low upstairsMains pressure throughout the house
Loft tankNeededNot needed
Safety devicesOpen vent pipe to the loft tankExpansion vessel or air bubble, pressure and temperature relief valves, discharge pipe and tundish
InstallerA competent plumberA qualified unvented installer under Building Regulations
Typical materialUsually copperUsually stainless steel
Works in a power cutYes, gravity fedYes, while the mains supply holds up
ShowersOften need a pump for good pressureGood pressure without a pump, if the mains is good

Vented cylinders

A vented (or open vented) cylinder is the traditional setup in many older homes. A cold water tank in the loft feeds the cylinder, usually in an airing cupboard, and hot water reaches your taps by gravity. An open vent pipe runs back up to the loft so the system can never build up pressure.

Vented systems are simple and forgiving. Their weakness is pressure: the lower the height between the loft tank and the tap, the weaker the flow, which is why upstairs showers on vented systems often need a pump. Loft tanks can also collect debris and need occasional checking.

Unvented cylinders

An unvented cylinder is fed directly from the mains and sealed, so the hot water comes out at close to mains pressure. That means strong showers anywhere in the house and no loft tanks, which frees up loft space.

Because it is a sealed, pressurised vessel of hot water, an unvented cylinder carries safety devices: an expansion vessel or internal air bubble to take up expansion, a pressure relief valve, a temperature relief valve, and a non self-resetting thermal cut-out. Approved Document G sets out that an unvented system needs at least two independent safety devices beyond its normal thermostat, and a discharge pipe running through a tundish to a safe place. Unvented cylinders must be fitted by a qualified installer, and manufacturers normally require an annual service to keep the guarantee.

The flow you get depends on your incoming mains. If the mains is weak, an unvented cylinder cannot make it stronger. Our guide to low water pressure in the whole house covers the checks a plumber makes before recommending one.

We install, service and repair them through our unvented cylinder service.

Direct vs indirect cylinders

This describes how the water in the cylinder is heated, and applies to both vented and unvented cylinders.

  • Indirect cylinders have a coil inside, through which hot water from the boiler (or heat pump) flows. The coil heats the water around it. Most cylinders in homes with a regular or system boiler are indirect, often with an immersion heater as a backup.
  • Direct cylinders have no boiler coil. They are heated by one or two electric immersion elements, often on an off-peak tariff overnight. They suit homes without a gas boiler, such as some flats.

Specialist cylinder types

Combination cylinders

A combination cylinder has a small cold water tank built on top of the hot water cylinder in one unit. It is a vented system that does not need a separate tank in the loft, which makes it useful in flats and homes without loft space. The trade-off is low pressure, because the tank is only just above the cylinder.

Solar cylinders (twin coil)

A solar cylinder has two coils. The lower coil takes heat from solar thermal panels, and the upper coil is heated by the boiler when the sun is not enough. Solar heat goes in first, and the boiler tops up.

Heat pump cylinders

Heat pumps produce water at lower temperatures than a gas boiler, so a heat pump cylinder has a much larger coil to transfer enough heat. A standard cylinder coil is usually too small to work well with a heat pump, which is why cylinders are normally replaced when a heat pump is fitted.

Thermal stores

A thermal store is different. It stores heating system water, not tap water, and heats fresh mains water as you use it through a coil or plate heat exchanger. It gives mains pressure hot water without being an unvented cylinder, and it is designed to take heat from several sources such as a boiler, a wood burner and solar panels.

Slimline and horizontal cylinders

Where space is tight, slimline cylinders (taller and narrower) and horizontal cylinders (lying on their side, for lofts or ceiling voids) are available in both vented and unvented versions.

Sizing and temperature

A cylinder needs to hold enough hot water for your household’s peak use, such as several showers in the morning, without running cold. Bigger households, more bathrooms and large baths all need a larger cylinder or a faster recovery time.

The HSE advises that hot water should be stored at 60 degrees or higher to control legionella bacteria. For that reason, cylinder thermostats should not be turned down below that level to save energy. Where scalding is a risk, thermostatic mixing valves at the taps or on the outlet reduce the temperature delivered.

Which type suits your home?

Your homeUsually suits
Good mains pressure, want strong showers, want loft space backUnvented cylinder
Weak mains pressureVented cylinder, possibly with a shower pump
Flat with no loftCombination cylinder, direct unvented cylinder, or a combi boiler
Solar thermal panelsTwin coil solar cylinder or thermal store
Wood burner with back boilerThermal store
Heat pumpHeat pump cylinder with a large coil
One bathroom, small household, low hot water demandA combi boiler, with no cylinder at all

If you are replacing your boiler as well, it is worth deciding on the cylinder at the same time. Our boiler installation team can compare a combi with a system boiler and cylinder for your home.

Safety points

  • Never tamper with or cap the discharge pipe or tundish on an unvented cylinder. If water is running from it, the cylinder needs attention.
  • Do not adjust the pressure or temperature relief valves on an unvented cylinder yourself.
  • Do not turn the cylinder thermostat below 60 degrees for long periods.
  • If the cylinder is leaking, turn off the cold supply to it and switch off the immersion and boiler, then call an engineer.

Common signs your cylinder needs attention

  • hot water running out faster than it used to
  • water dripping from the tundish or discharge pipe on an unvented cylinder
  • rust-coloured water, damp patches or a leak around the cylinder
  • a banging, rumbling or hissing noise as it heats, which can point to scale in hard water areas like most of Hertfordshire
  • no hot water while the heating works, covered in our guide to no hot water but heating works

In hard water areas, a water softener helps protect cylinders, coils and immersion elements from scale.

What it costs with Vantage

For repairs, in normal working hours there is no call-out fee. After the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page.

New cylinders are quoted as a fixed price after a free survey, so the price you agree is the price you pay. If you are replacing your boiler too, you can get your price online in a couple of minutes with our boiler quote tool. Our work carries a 12 month labour guarantee.

Frequently asked questions

What is the difference between a vented and unvented cylinder?

A vented cylinder is fed by a cold water tank in the loft and gives hot water by gravity, so pressure can be low. An unvented cylinder is fed from the mains and gives hot water at mains pressure, but needs safety devices and a qualified installer.

How do I know if my cylinder is vented or unvented?

A vented cylinder usually has a cold water tank in the loft feeding it and is often copper with foam insulation. An unvented cylinder usually has a white or grey outer casing, an expansion vessel nearby, and a discharge pipe with a tundish.

Does an unvented cylinder need servicing?

Yes. Manufacturers normally require an annual service to keep the guarantee, which checks the safety valves, expansion vessel and controls.

Can I replace a vented cylinder with an unvented one?

Usually, yes, if your mains pressure and flow are good enough. A plumber should measure both first, because an unvented cylinder cannot improve a weak mains supply.

Do I need a hot water cylinder with a combi boiler?

No. A combi boiler heats water on demand, so there is no cylinder. Homes with more than one bathroom or high hot water use may be better served by a system boiler and cylinder.

Help in Hertfordshire, Bedfordshire and Cambridgeshire

If you are choosing a new cylinder, or your current one is leaking or running out of hot water, our engineers can advise on the right type and fit it properly. See our unvented cylinder page or call 01462 506374, answered 24 hours a day, 7 days a week.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.