Skip to main content

Vantage Plumbing and Heating

Types of Taps Explained: A Plumber’s Buying Guide

Hertfordshire, Bedfordshire & Cambridgeshire

Fully Stocked Vans12 Month Labour GuaranteeGas Safe Registered 956889

The main types of tap are pillar taps (separate hot and cold), mixer taps (hot and cold through one spout), monobloc taps (a mixer on a single hole), wall-mounted taps, bridge taps, thermostatic taps, sensor taps and boiling water taps. The right choice depends less on style than on three practical things: how many holes your sink or bath has, what water pressure your home has, and how the tap controls the flow inside.

In short

  • Pillar taps are a separate hot and cold pair. Mixer and monobloc taps blend both through one spout.
  • Check the tap holes in your basin, sink or bath before you buy. The tap must suit the hole count.
  • Many modern taps need mains pressure. On a low pressure, tank-fed system, buy a tap rated for low pressure.
  • Inside, most new taps use ceramic discs or cartridges, which turn a quarter or half turn and last well. Older taps use rubber washers.
  • Hard water across most of Hertfordshire means limescale on aerators and cartridges, so choose a tap with easy-to-get spares.

Start with three questions

Before you look at finishes, answer these:

  1. How many tap holes are there? One hole needs a monobloc. Two holes need a pillar pair or a two-hole mixer. Three holes suit a three-hole mixer. A basin or sink with no holes needs a wall-mounted tap, which means pipework in the wall.
  2. What water pressure do you have? If you have a combi boiler or an unvented cylinder, both hot and cold usually come at mains pressure. If you have a tank in the loft feeding a hot water cylinder, the hot water is low pressure, and many modern taps will give a disappointing flow.
  3. Where does the tap go? Kitchen, basin and bath taps are different products with different spout heights and reaches.

If you are not sure what system you have, or your flow is weak at every tap, our guide to low water pressure in the whole house explains what a plumber checks. If you would rather not do it yourself, our general plumbing repairs team fits taps of every type.

The main types of tap

Pillar taps

A pair of separate taps, one hot and one cold, each on its own hole. They are the traditional British choice and suit older basins, baths and period bathrooms. They cope well with low pressure. The drawback is that you cannot blend the water to a comfortable temperature at the spout.

Mixer taps

A mixer brings hot and cold water to a single spout, so you get water at the temperature you choose. It can have two handles or one lever. Kitchen mixers usually have a tall swivel spout. Basin mixers are shorter.

Monobloc taps

A monobloc is a mixer that sits on a single tap hole. It is now the most common tap on new kitchen sinks and basins. Most monoblocs have a single lever controlling both flow and temperature.

Bridge taps

A bridge tap has two handles joined by a horizontal bar, with the spout rising from the middle. It needs two holes and gives a traditional look in a kitchen or bathroom.

Wall-mounted taps

The tap body is fixed to the wall above the basin, bath or sink, with the pipework hidden behind. They keep the worktop or basin clear and look clean, but they have to be planned in at the start of a renovation, because the pipes run inside the wall and the spout reach has to match the basin.

Bath taps and bath shower mixers

Bath taps come as pillar pairs, deck mounted bath fillers and bath shower mixers with a hand shower on a hose. Baths hold a lot of water, so a bath tap with a good flow matters more than it would at a basin.

Thermostatic taps

A thermostatic tap has a built-in valve that holds the water at a set temperature, even if the pressure changes when someone runs another tap. They are a good choice for homes with children or older people. In new homes in England, building regulations require the hot water supply to a bath to be limited to no more than 48°C, usually by a blending valve or thermostatic control, so this is often designed in from the start.

Sensor taps

Sensor taps turn on when you put your hands underneath and turn off when you move them away. They are common in commercial toilets and are becoming more popular at home for hygiene. They need a power supply or batteries.

Pull-out and spray taps

A kitchen tap with a spray head on a hose that pulls out of the spout, useful for rinsing pans and filling buckets. Check the hose has room to move inside the cupboard below.

Boiling water taps

A boiling water tap gives near boiling water on demand from a small tank under the sink, usually alongside normal hot and cold. They need space in the cupboard and an electrical supply, and most have child resistant controls. In hard water areas like most of Hertfordshire, the filter needs changing as the maker recommends to keep scale down.

How the inside of a tap works

MechanismHow it turnsFound inWhat wears out
Compression (washer)Several full turnsOlder pillar tapsRubber washer, causing drips
Ceramic discQuarter or half turnMost modern two-handle tapsDisc cartridge, less often
Single lever cartridgeLever moves up and down, left and rightMonoblocs and single lever mixersCartridge, often from limescale
Thermostatic cartridgeTemperature dial or leverThermostatic tapsCartridge, especially in hard water

A dripping compression tap usually needs a new washer. A dripping ceramic or cartridge tap usually needs a new cartridge, which must be the right one for that tap. This is why it is worth buying taps from a maker whose spares are easy to find. Our general plumbing repairs team fixes dripping taps, stiff levers and leaks under the sink.

Types of tap compared

Tap typeTap holesGood on low pressure?Best for
Pillar taps2Usually yesTraditional basins and baths
Monobloc mixer1Only if rated for low pressureModern kitchens and basins
Three-hole mixer3VariesLarger basins and baths
Bridge tap2VariesTraditional kitchens
Wall-mounted0 (wall)VariesClean, modern bathrooms
Thermostatic1 or 2Check the minimum pressureFamilies, safety
Boiling water1Needs mains cold supplyKitchens

Water regulations and safety

Every tap connected to the mains has to meet the Water Supply (Water Fittings) Regulations 1999. Look for taps that are approved under a recognised scheme such as WRAS, which shows the tap has been tested against those rules. Cheap unbranded taps bought online are not always compliant.

Mixer taps bring hot and cold together inside the tap. If your hot water comes from a tank in the loft and your cold comes from the mains, the pressures are unbalanced. The water fittings rules then require suitable backflow protection, such as check valves, so mains pressure cold water cannot push back into the hot supply. A plumber will check this when fitting a mixer on an older system.

Before you fit a tap yourself

  • Turn off the isolation valves under the sink, or the stop tap, and open the tap to drain the pipe.
  • Do not overtighten flexible connectors. Hand tight plus a small turn with a spanner is usually enough.
  • Check under the sink for drips for a day afterwards. A slow leak inside a cupboard can rot the base before anyone notices.
  • If your pipes have no isolation valves, or your stop tap will not turn, call a plumber rather than forcing it.

Mistakes to avoid

  • Buying a mains pressure tap for a low pressure system. The flow will be weak. Check the tap’s minimum pressure against your system.
  • Ignoring the hole count. A monobloc will not cover the holes left by pillar taps.
  • Forgetting spout reach. A spout that is too short splashes the back of the basin. Too long and it splashes you.
  • Choosing a tap with no spares. In hard water, cartridges and aerators wear. If you want to cut scale throughout the house, our water softener installation service can help.

What it costs with Vantage

In normal working hours there is no call-out fee. After the first hour, time is charged in half-hour steps, and parts are quoted before we fit them. You can supply your own tap or we can source one. Evening, weekend and overnight visits are charged at the out-of-hours rates. Every rate is published on our prices page, so you know what you will pay before we arrive. If new taps are part of a new bathroom, our bathroom installation is quoted as a fixed price after a free survey.

Our plumbing work carries a 12 month labour guarantee, and bathrooms we install carry a 12 month guarantee.

Frequently asked questions

What is the difference between a mixer tap and a monobloc tap?

A mixer tap blends hot and cold through one spout and can sit on one, two or three holes. A monobloc is a type of mixer that sits on a single hole. So every monobloc is a mixer, but not every mixer is a monobloc.

Which taps are best for low water pressure?

Pillar taps and taps specifically rated for low pressure work best. The tap’s product information should give a minimum working pressure. If your hot water is fed from a tank in the loft, choose a tap rated for that.

Why does my new mixer tap have a weak flow?

The most common reasons are low pressure on the hot side, a blocked aerator, or restricted isolation valves under the sink. On a tank-fed system, a mains pressure tap will often give a weak hot flow.

How long do taps last?

A good quality tap can last many years. In hard water, aerators and cartridges wear sooner, but they can usually be replaced without changing the whole tap, as long as spares are available.

Can I replace a tap myself?

Many people can swap a basin or kitchen tap if the pipes have isolation valves and the connections are standard. Wall-mounted taps, bath taps and anything that means changing pipework are better left to a plumber.

Tap fitting and repairs in Hertfordshire, Bedfordshire and Cambridgeshire

If you need a new tap fitted, a drip fixed or advice on what will work with your water pressure, our own plumbers can help from our Stevenage base. We are rated 4.9 on Google and our phone is answered 24 hours a day, 7 days a week. See our general plumbing repairs page or call 01462 506374.

What our customers say

Speak to a local engineer

Vantage Plumbing and Heating covers Hertfordshire, Bedfordshire and the surrounding areas. Call and talk to an engineer, or send us the details and we will come back to you with a price.

Gas Safe registered, number 956889. Emergency line answered 24/7.

Trusted & Accredited Professionals
Checkatrade approved trader
City and Guilds qualified engineers
BPEC certified engineers
Gas Safe registered engineers
Elite CHAS accreditation
London and South East England Prestige Awards 2022 winner
Veriforce CHAS accredited contractor

Rather have an engineer look at it?

Call the office, message us on WhatsApp or ask for a callback. We cover Hertfordshire, Bedfordshire and the surrounding areas.

Why choose Vantage

Rated 4.9 on Google from more than 700 reviews across Google, Checkatrade and Trustatrader. Qualified, accredited engineers, a fixed price before any work begins and a labour guarantee on every job, from an established local company with an office team you can actually reach. No job too small.

The Vantage Plumbing and Heating fleet of five fully stocked liveried vans

Gas Safe registered

Company registration 956889. Every gas engineer carries their own Gas Safe ID card, and you can ask to see it.

Refcom F-Gas certified

REF1024550. Legally required for air conditioning installation and servicing, and we hold it.

CHAS Elite accredited

Veriforce CHAS assessed for health and safety, which is why commercial clients and landlords use us.

City & Guilds and BPEC qualified

Qualified, insured engineers on every job. No subcontracted strangers.

700+ reviews, 4.9 on Google

Across Google, Checkatrade and Trustatrader. Read them before you book.

Labour guarantee on every job

12 months on repairs, installations and everything else. Two years on a full bathroom refit. If anything we did develops a fault, we come back and put it right.

Fixed price before we start

The price is agreed with you before any work begins. No hidden extras on the invoice.

24/7, answered by a person

The emergency line is answered every day of the year by someone who can send an engineer, not a call centre.

Fully stocked vans

Five vans carrying the parts that fail most often, so most jobs are fixed on the first visit.

An office team behind every job

An established local business with multiple engineers and a dedicated office team to keep you informed.

Vaillant myREWARDS and Ideal Max accredited

Accredited installer status means extended manufacturer warranties on the boilers we fit.

Emergency response within the hour

Our average response to an emergency call is under an hour across Hertfordshire, Bedfordshire and Cambridgeshire.

Quick check

Do we cover your postcode?

We work across Hertfordshire, Bedfordshire, Cambridgeshire, Milton Keynes and North, East and West London, including Hitchin, Stevenage, St Albans, Luton and Cambridge. Pop your postcode in and see straight away.

If we cover you, tell us what you need and how soon, and we will ring you back. Prefer to talk now? Call 01462 506 374, answered by a person 24/7.

✓ Yes, we cover you. Fill in the short form below and we will ring you back.
We might not cover your area yet. Send it anyway: fill in the short form below and we will ring you back and tell you honestly whether we can reach you.
Sorry, we do not work in South London. For anything else, ring 01462 506 374.